Aggregate Crushing Value Specification

1. Home
3. Aggregate Crushing Value Specification

Determination Of Aggregate Crushing Value

The apparatus of the aggregate crushing value test as per IS 2386 Part IV 1963 consists of 1 A 15cm diameter open ended steel cylinder with plunger and base plate, of the general form and dimensions as shown in Fig 1. 2 A straight metal tamping rod

Is 9376 1979 Specification For Apparatus For

IS9376-1979 1. SCOPE 1.1 This standard covers requirements of the apparatus for measuring aggregate crushing value and ten percent fines value. 1.1.1 Two sizes of apparatus are covered in this standard, one with 150 mm cylindrical cell and the other with 75 mm cylindrical cell. 2.

Aggregate Crushing Value Test Determine Aggregate

Aggregate crushing value test on coarse aggregates gives a relative measure of the resistance of an aggregate crushing under gradually applied compressive load. Coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected to a specified load under standardized conditions.

Relationship Between Aggregate Crushing

between aggregate crushing value ACV and ten percent fines aggregate crushing value TFV for some aggregates in Nigeria. Such a mathematical relationship, usually established through regression modelling on data collected, is useful in saving time and money cost on site through estimating one variable when another is known.

Aggregate Crushing Value Civil Engineering Portal

AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS 2386 Part IV 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm Procedure to determine Aggregate Crushing Value i The aggregates passing through 12.5mm

Is 9376 Specification For Apparatus For Measuring

Title of Legally Binding Document Specification for apparatus for measuring aggregate crushing value and ten percent fines value Number of Amendments Equivalence Superceding Superceded by LEGALLY BINDING DOCUMENT Step Out From the Old to the New--Jawaharlal Nehru Invent a new India using knowledge.--Satyanarayan Gangaram Pitroda

Eta0401 Ballast Specification Version 12 Master

6.8.1 Aggregate Crushing Value The aggregate crushing value of the ballast material when determined in accordance with AS1141.21, for the fraction of material passing the 26.5 mm test sieve and retained on 19.0 mm test sieve shall be 25 maximum Note The aggregate crushing value of the ballast material when determined in accordance

Is 383 1970 Specification For Coarse And Fine

2.1.2 Crushed Stone Sand - Fine aggregate produced by crushing hard stone. 2.1.3 Crushed Grace1 Sand - line aggregate produced by crushing natural gravel. . 2.2 Coarse Aggregate -- Aggregate most of which is retained on 475-mm IS Sieve and containing only so much finer material as is permitted for

Specification For Aggregate As Per Indian

Mar 15, 2018 Coarse Aggregate -. 1- 5 for uncrushed , 2- 2 for Crushed , 3- 2 for Manufactured. Aggregate Crushing Value -. The aggregate crushing value shall not exceed 45 for aggregate used for concrete other than for wearing surface. The aggregate crushing value shall not exceed 30 for aggregate used for wearing surfaces such as runways, roads, and ...

Standard Of Crushing Value Of Coarse Aggregates For

Jan 20, 2020 In current Chinese technical specification, the crushing value of the coarse aggregate for surface layer of asphalt pavement is no greater than 26 . So, the crushing value standard of basalt coarse aggregate used in PA mixture should be increased to not more than 261.48 17.6.

Aggregate Impact Value Test Impact Test Of Aggregate

Read More Aggregate Crushing Value Test Procedure and Result. Objectives of Impact Value Test. This method of test used to measure the impact value of aggregate use in the construction of Highway pavement and concrete structure. Reference-Aggregate impact value

Aggregate Crushing Value Apparatus Zeal International

Aggregate Crushing Value Apparatus. ZI 5014. StandardsIS 2386 PART-IV amp BS 812111. Specification The Aggregate Crushing Value ACV test set provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Each set consists of steel cylinder, plunger, base plate, cylindrical measure and ...

Is 23864 1963 Methods Of Test For Aggregates For

gate of aggregate crushing value 30 or higher, the result may be anomalous, and in such cases the ten percent fines value should be determined instead. NOTE 2 - The standard aggregate crushing test shall be made on aggre a 12.5-mm IS Sieve and retained on a IO-mm IS Sieve. ...

Is 9376 1979 Specification For Apparatus For

SPECIFICATION FOR APPARATUS FOR MEASURING AGGREGATE CRUSHING VALUE AND TEN PERCENT FINES VALUE 0. FOREWORD 0.1 This Indian Standard was adopted by the Indian Standards Institution on 20 December 1979, after the draft finalized by the Cement and

Aggregate Crushing Value Apparatus Sethi Steel Amp Metal

Aggregate Crushing value Apparatus for determining the Aggregate Crushing Value Specification of apparatus consists Specification of It consists A steel cylinder 75 mm dia, a plunger and a steel base plate. The surfaces coming into contact with the aggregate are case hardened. First Name Contact Number Message Submit Form

Determination Of Aggregate Crushing Value

The aggregate crushing value gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Crushing value is

Is 9376 1979 Specification For Apparatus For Measuring

IS 9376 1979 Specification for apparatus for measuring aggregate crushing value and ten percent fines value. Disclosure to Promote the Right To Information.

Standard Of Crushing Value Of Coarse Aggregates For

4 rows Jan 20, 2020 8. Recommended Crushing Value Standard of Coarse Aggregate in PA Mixture. In current Chinese ...